How To Knit a Gauge Swatch

How To Knit a Gauge Swatch

So many things can go wrong with your knitting if you don’t meet the gauge specified in your knitting pattern. Your sweater can be to small, or comically large. Your one skein knitting projects can turn into two skein knitting projects, dipping into your knitting budget. Your hat pattern sized to fit an adult can be suited only for a newborn. The first defense against ill fitting knitting project is to swatch for your project. Below I’ve written the key factors in creating a gauge swatch. If you’d like to read more about gauge please read my article on Gauge: How one project knit by two different knitters equals two different FOs. A story. here.

1. Locate the knitting needle, yarn and gauge information on your pattern.

For Example:
Size US 5/3.75 mm Knitting Needles, or size needed to get gauge.

Yarn One 100 gram ball of Zen Yarn Garden Serenity Silk Single [75% Superwash Merino, 15% Cashmere, 10% Silk]. 774 yards/803 meters. Total yardage: 740 yards/ 710 meters.

28 stitches and 30 rows over 4 inches in Stockinette Stitch.

2. Cast on for your swatch.

Using the above information that means you’d cast on 28 stitches with a US 5 Knitting Needle, a skein of Zen Yarn Garden Serenity Silk and knit 30 rows in Stockinette Stitch.

If you’re concerned that you may not have enough yarn, instead of binding off the swatch try putting the end stitches of your swatch on waste yarn. That way you can undo the swatch if you need the extra yarn.

3. Soak your swatch in wool wash.

I like Euclan but there are a few options available like Soak and Kookaburra.

4. Press your swatch dry with a dry towel.

Do not wring the water out! That can damage the knit fabric.

Adjust pins!

5. Block your swatch exactly how you normally block your shawls since that’s how you’ll treat this one when it’s done!

6. Measure your swatch.

From the Gauge information above your swatch should measure 4 inches from side to side and 4 inches from top to bottom. If the swatch is shorter than 4 inches repeat steps 1-6 with a larger needle. If your swatch is longer than 4 inches repeat steps 1-6 with a smaller needle.

Fluid Velocity Shawl

Row gauge can affect your yarn usage! You should do your best to get close to row gauge. If you are off and are soaking up more yarn than the stated gauge you could run out before your knitting project is finished.

Something to keep in mind is that many knitters use up more yarn on a purl row than a knit row.

Gauge Short Cuts, Quick and Dirty Knitting Methods

If you want the finished item to be smaller try knitting with smaller yarn and needles. For example, if original pattern calls for US 9 Needle and Bulky yarn, try US 7 and Worsted yarn. Wash swatch and measure gauge.

If you want the finished item to be larger try knitting with larger needles and yarn. For example, if original pattern calls for US 5 Needle and DK yarn, try US 7 and Worsted yarn. Wash swatch and measure gauge.

If you like the fabric with a particular yarn and needle but the finished garment is too small, you can try knitting a larger size. Or if the finished garment is too large you can try knitting a smaller size.

For example if the pattern comes in (32, 34, 36) inch chest measurements and the size 34 is too small with your gauge, try the 36. If you knit the 34 inch size and it is too big, try knitting the 32 size.

Special note: If you change yarns to a heavier yarn (i.e. go from sport weight to bulky weight) you will need more ease in the pattern. So go up a size or two.

Gauge Math

If you’ve tried different yarns and needles and just can’t get the right gauge you have the option of recalculating the pattern to fit the gauge you get with the needles and yarn of your choice.
The basic equation is:

Your gauge                                 x
__________       =        __________ ;
Pattern gauge        Pattern Stitch Number

Your gauge is 5 st/in. The stated pattern gauge is 6 st/in. The hat pattern calls for 64 stitches cast on. Since your gauge is different but you want the same finished size, plug everything into the equation where x becomes the new number to cast on.
5         x
__ = __ ;
6       64

Rearrange to solve for x.

x = (5*64)/6 = 53.33

Round the answer down to 53 from 53.33. The hat pattern starts with a 2 by 2 rib. So the cast on number must be divisible by 4. 53/4 is not an even number, but 52/4 is even. Meaning it is divisible by 4 and will work with 2 by 2 rib.

You can redo every pattern number in this manner, no matter if it’s a sweater, hat, or sock. The method works because it uses ratios and proportions.

A simplified version of the original equation is:

(Your Gauge*Pattern Stitch Number)/ Pattern Gauge = x.

All you need to do is plug in the numbers for each section to solve for the new numbers based on your gauge.

Dig through our archives.